smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-5mx-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E680 Serial Number: TMA55C3J3D1R8L LU WWN Device Id: 5 000cca 7deefc16a Firmware Version: GG2OAF10 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Sep 10 07:05:16 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 112) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 202 202 033 - 1 4 Start_Stop_Count -O--C- 069 069 000 - 49872 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 078 078 000 - 9787 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 4268 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 221 193 Load_Cycle_Count -O--C- 073 073 000 - 274192 194 Temperature_Celsius -O---- 230 230 000 - 26 (Min/Max 14/43) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 6288 hours (262 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 48 00 00 01 2c 0f d0 01 00 Error: UNC at LBA = 0x012c0fd0 = 19664848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 68 00 00 01 2c 0f 98 40 00 00:00:11.588 READ FPDMA QUEUED b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:00:11.588 SMART RETURN STATUS 2f 00 00 00 01 00 00 00 00 00 10 28 00 00:00:11.587 READ LOG EXT 60 00 80 00 58 00 00 01 2c 0f 98 40 00 00:00:08.066 READ FPDMA QUEUED b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:00:08.065 SMART RETURN STATUS Error 2 [1] occurred at disk power-on lifetime: 6288 hours (262 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 48 00 00 01 2c 0f d0 01 00 Error: UNC at LBA = 0x012c0fd0 = 19664848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 58 00 00 01 2c 0f 98 40 00 00:00:08.066 READ FPDMA QUEUED b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:00:08.065 SMART RETURN STATUS 2f 00 00 00 01 00 00 00 00 00 10 28 00 00:00:08.065 READ LOG EXT 60 00 80 00 48 00 00 01 2c 0f 98 40 00 00:00:04.573 READ FPDMA QUEUED 60 00 80 00 40 00 00 01 2c 0f 18 40 00 00:00:04.572 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 6288 hours (262 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 48 00 00 01 2c 0f d0 01 00 Error: UNC at LBA = 0x012c0fd0 = 19664848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 48 00 00 01 2c 0f 98 40 00 00:00:04.573 READ FPDMA QUEUED 60 00 80 00 40 00 00 01 2c 0f 18 40 00 00:00:04.572 READ FPDMA QUEUED 60 00 80 00 38 00 00 01 2c 0e 98 40 00 00:00:04.572 READ FPDMA QUEUED 60 00 80 00 30 00 00 01 2c 0e 18 40 00 00:00:04.571 READ FPDMA QUEUED 60 00 80 00 28 00 00 01 2c 0d 98 40 00 00:00:04.570 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 25/26 Celsius Lifetime Min/Max Temperature: 14/43 Celsius Specified Max Operating Temperature: 30 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (66) Index Estimated Time Temperature Celsius 67 2024-09-10 04:58 ? - 68 2024-09-10 04:59 26 ******* 69 2024-09-10 05:00 27 ******** 70 2024-09-10 05:01 28 ********* 71 2024-09-10 05:02 ? - 72 2024-09-10 05:03 36 ***************** 73 2024-09-10 05:04 36 ***************** 74 2024-09-10 05:05 37 ****************** ... ..( 3 skipped). .. ****************** 78 2024-09-10 05:09 37 ****************** 79 2024-09-10 05:10 36 ***************** 80 2024-09-10 05:11 36 ***************** 81 2024-09-10 05:12 ? - 82 2024-09-10 05:13 36 ***************** 83 2024-09-10 05:14 37 ****************** 84 2024-09-10 05:15 37 ****************** 85 2024-09-10 05:16 ? - 86 2024-09-10 05:17 37 ****************** 87 2024-09-10 05:18 37 ****************** 88 2024-09-10 05:19 37 ****************** 89 2024-09-10 05:20 ? - 90 2024-09-10 05:21 36 ***************** 91 2024-09-10 05:22 37 ****************** ... ..( 5 skipped). .. ****************** 97 2024-09-10 05:28 37 ****************** 98 2024-09-10 05:29 36 ***************** 99 2024-09-10 05:30 36 ***************** 100 2024-09-10 05:31 37 ****************** ... ..( 2 skipped). .. ****************** 103 2024-09-10 05:34 37 ****************** 104 2024-09-10 05:35 38 ******************* ... ..( 18 skipped). .. ******************* 123 2024-09-10 05:54 38 ******************* 124 2024-09-10 05:55 37 ****************** 125 2024-09-10 05:56 36 ***************** ... ..( 8 skipped). .. ***************** 6 2024-09-10 06:05 36 ***************** 7 2024-09-10 06:06 35 **************** ... ..( 11 skipped). .. **************** 19 2024-09-10 06:18 35 **************** 20 2024-09-10 06:19 34 *************** 21 2024-09-10 06:20 34 *************** 22 2024-09-10 06:21 ? - 23 2024-09-10 06:22 ? - 24 2024-09-10 06:23 37 ****************** ... ..( 2 skipped). .. ****************** 27 2024-09-10 06:26 37 ****************** 28 2024-09-10 06:27 ? - 29 2024-09-10 06:28 38 ******************* ... ..( 2 skipped). .. ******************* 32 2024-09-10 06:31 38 ******************* 33 2024-09-10 06:32 ? - 34 2024-09-10 06:33 26 ******* 35 2024-09-10 06:34 28 ********* 36 2024-09-10 06:35 28 ********* 37 2024-09-10 06:36 29 ********** 38 2024-09-10 06:37 30 *********** 39 2024-09-10 06:38 31 ************ ... ..( 2 skipped). .. ************ 42 2024-09-10 06:41 31 ************ 43 2024-09-10 06:42 32 ************* 44 2024-09-10 06:43 31 ************ ... ..( 2 skipped). .. ************ 47 2024-09-10 06:46 31 ************ 48 2024-09-10 06:47 32 ************* 49 2024-09-10 06:48 33 ************** 50 2024-09-10 06:49 33 ************** 51 2024-09-10 06:50 34 *************** 52 2024-09-10 06:51 34 *************** 53 2024-09-10 06:52 34 *************** 54 2024-09-10 06:53 35 **************** ... ..( 2 skipped). .. **************** 57 2024-09-10 06:56 35 **************** 58 2024-09-10 06:57 36 ***************** 59 2024-09-10 06:58 36 ***************** 60 2024-09-10 06:59 ? - 61 2024-09-10 07:00 26 ******* 62 2024-09-10 07:01 27 ******** 63 2024-09-10 07:02 28 ********* 64 2024-09-10 07:03 29 ********** 65 2024-09-10 07:04 ? - 66 2024-09-10 07:05 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 63 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS